1. Acrylic cutting processing, single-edged spiral milling cutter is recommended, (milling cutter products in the processing of acrylic, aluminum, MDF and other products, regardless of the processing speed and quality have superior performance; engraving knife products In the processing of aluminum and copper, stainless steel, iron is also not unusual) is characterized by the process of smokeless and odorless, fast, high efficiency, non-stick crumbs, truly environmentally friendly, its special manufacturing process to ensure the processing of acrylic does not burst, very Fine knife pattern (even without knife pattern), smooth and smooth surface, which is beyond the reach of other manufacturers' tools and can not be compared. The surface must be matte, and a double-edged three-edge spiral cutter is recommended.

2. The MDF cutting process (for advertising opening), users who have used this tool will be shocked by the high efficiency and high efficiency of high-quality milling, which is why they often put it down. The market has always been very reflective. it is good. It is recommended to use a double-edged and large-flux spiral milling cutter, which has two high-capacity chip flutes and a double-edged design. It not only has good chip evacuation function, but also achieves good tool balance. When processing medium-density boards, Not black, no smoke, long life and other characteristics. The A or AA series of tools will perform better in terms of service life and processing efficiency.

3. Aluminium sheet cutting processing, the use of single-edge special aluminum milling cutter is recommended. No sticking knife during processing, high speed and high efficiency.

4. Precision small relief processing, it is recommended to use a round bottom knife.

5. Cork, MDF, original wood, PVC, acrylic large deep relief processing, recommended single-edged spiral ball end mill.

6. There is no burr cutting process on the upper and lower surfaces. It is recommended to use a single-blade, double-edged upper and lower cutting cutter.

7. For metal engraving, it is recommended to use a single-edged, double-edged straight groove flat-bottomed knife.

8. The company's 3D carving knife, high concentricity, sharp edges, can do precision 3D engraving processing.

9. High-density board, solid wood recommended the use of edge milling cutter. The company exclusively offers 3.175X15, 17 and 4MM, 6MM shank milling cutters, the processing effect is sure to make users satisfied. You can also use double-edged large chip cutter.

10. Plywood, plywood processing, it is recommended to use double-edged straight groove milling cutter.

11. With the use of the lower knife, the upper surface of the processed product is free from burrs, and it will not be rocked during processing.

12. For milling cutters for metal molds, it is recommended to use tungsten steel cutters with a black plated surface and hard titanium.

13. Acrylic mirror engraving is recommended to use diamond carving knife.

14. The use of multi-striped milling cutters is recommended for roughing chipboards.

15. Diamond carving tool A professional tool developed by our company for aluminum, copper, iron, acrylic mirror processing and marble processing.

16. Lens combination knife: acrylic special tool PMMA board, PC board cutting special milling cutter

This kind of tool is mainly used for high-speed cutting of flat panel TV panel cutting, LCD panel cutting, PMMA signage, mobile phone lens, MP4 lens, DVD nameplate, LCD film window, etc.

1. Acrylic cutting processing, single-edged spiral milling cutter is recommended, (milling cutter products in the processing of acrylic, aluminum, MDF and other products, regardless of the processing speed and quality have superior performance; engraving knife products In the processing of aluminum and copper, stainless steel, iron is also not unusual) is characterized by the process of smokeless and odorless, fast, high efficiency, non-stick crumbs, truly environmentally friendly, its special manufacturing process to ensure the processing of acrylic does not burst, very Fine knife pattern (even without knife pattern), smooth and smooth surface, which is beyond the reach of other manufacturers' tools and can not be compared. The surface must be matte, and a double-edged three-edge spiral cutter is recommended.

2. The MDF cutting process (for advertising opening), users who have used this tool will be shocked by the high efficiency and high efficiency of high-quality milling, which is why they often put it down. The market has always been very reflective. it is good. It is recommended to use a double-edged and large-flux spiral milling cutter, which has two high-capacity chip flutes and a double-edged design. It not only has good chip evacuation function, but also achieves good tool balance. When processing medium-density boards, Not black, no smoke, long life and other characteristics. The A or AA series of tools will perform better in terms of service life and processing efficiency.

3. Aluminium sheet cutting processing, the use of single-edge special aluminum milling cutter is recommended. No sticking knife during processing, high speed and high efficiency.

4. Precision small relief processing, it is recommended to use a round bottom knife.

5. Cork, MDF, original wood, PVC, acrylic large deep relief processing, recommended single-edged spiral ball end mill.

6. There is no burr cutting process on the upper and lower surfaces. It is recommended to use a single-blade, double-edged upper and lower cutting cutter.

7. For metal engraving, it is recommended to use a single-edged, double-edged straight groove flat-bottomed knife.

8. The company's 3D carving knife, high concentricity, sharp edges, can do precision 3D engraving processing.

9. High-density board, solid wood recommended the use of edge milling cutter. The company exclusively offers 3.175X15, 17 and 4MM, 6MM shank milling cutters, the processing effect is sure to make users satisfied. You can also use double-edged large chip cutter.

10. Plywood, plywood processing, it is recommended to use double-edged straight groove milling cutter.

11. With the use of the lower knife, the upper surface of the processed product is free from burrs, and it will not be rocked during processing.

12. For milling cutters for metal molds, it is recommended to use tungsten steel cutters with a black plated surface and hard titanium.

13. Acrylic mirror engraving is recommended to use diamond carving knife.

14. The use of multi-striped milling cutters is recommended for roughing chipboards.

15. Diamond carving tool A professional tool developed by our company for aluminum, copper, iron, acrylic mirror processing and marble processing.

16. Lens combination knife: acrylic special tool PMMA board, PC board cutting special milling cutter

This kind of tool is mainly used for high-speed cutting of flat panel TV panel cutting, LCD panel cutting, PMMA signage, mobile phone lens, MP4 lens, DVD nameplate, LCD film window, etc.